F Ball - F58 Styccobond Rubber Floorcovering Adhesive

Bulk Buy Discount
In stock
F Ball - F58 Styccobond Rubber Floorcovering Adhesive
  • Available for Next Day Delivery
  • FREE Delivery when you spend over £125

F Ball - F58 (15ltr) Styccobond Rubber Floorcovering Adhesive

STYCCOBOND F58 is an acrylic emulsion adhesive, which is designed to give a high bond strength and strong initial tack. It is protected against biodegradation and is suitable for use over normal underfloor heating installations.

STYCCOBOND F58 can be used for securing a wide range of rubber sheet and tile floorcoverings. 

It can be applied to STOPGAP smoothing underlayments, structurally sound, smooth, dry subfloors of concrete and sand/cement screed, plywood, flooring grade chipboard and hardboard. 

STOPGAP Waterproof Surface Membranes, sound flooring grade asphalt and other non-absorbent surfaces must be skimmed with a minimum of 3mm of the appropriate STOPGAP smoothing underlayment.

Technical Information:

  • Appearance: Creamy Liquid
  • Colour: Cream Yellow
  • Available in 15ltr and 5ltr capacity
  • OpenTime (approx.): Up to 30 minutes depending on temperature, humidity and absorbency of the subfloor
  • Coverage (approx.): 3m2 per litre with an A2 / 1.5mm x 3mm trowel
    15 litres Tub = 45m2
    5 litres Tub = 15m2
    Note: Coverage rates will depend on the condition and absorbency of the subfloor


Site conditions vary and will have an impact upon the application characteristics of the adhesive.

Holding the trowel at an angle of 60°, spread the adhesive evenly over an area of subfloor that can be covered whilst the adhesive remains receptive and gives good transfer. Allow the adhesive sufficient time to reach a wet pasty tacky consistency but still enabling full transfer to the back of the floorcovering. When installing tiles, leave the adhesive for approximately 10 minutes before placing the flooring – this will help to reduce the potential for sliding.

Following the floorcovering manufacturers installation instructions lay the floorcovering into the adhesive gradually expelling air using a cork board. Press from the centre outwards using a cork board or carpeted STYCCOBOND GLYDA to ensure the floorcovering is laying flat, as soon as the adhesive begins to secure the floorcovering, roll using a flooring roller, end-to-end and side-to-side to ensure overall contact. 30 minutes later when the floor has been completely covered roll as necessary to ensure overall contact is maintained.

For any areas under question please consult the F Ball Technical team.


Surplus adhesive may be removed from the surface of the flooring whilst it is still wet, using a cloth dampened with water. Allow the adhesive to dry overnight before commencing seam welding operations. Using a flooring roller on 2mm thick rubber floorcoverings whilst the adhesive is still wet will promote bubbling.


STYCCOBOND A2 notched trowel, F. Ball 68kg flooring roller, Trimming knife, Cork Board, STYCCOBOND GLYDA. Tools should be cleaned with warm soapy water while the adhesive is still wet.


Store between 5ºC and 30°C. Protect from frost.

Shelf Life:

12 months in unopened containers stored under good conditions.

Delivery Information

We aim to dispatch all orders within 2 working day of receipt. Occasionally public holidays, weekends, weather events, or extremely busy periods may result in extended delivery times. In these circumstances, we will endeavour to communicate with you about the delay and resolve and resulting issues.

Please note that we do not make delivery date promises, however:

- Orders placed before 1pm on a weekday will be processed the same day.

- Orders placed after 1pm on a weekday will be processed the following morning. 

- Orders placed after 1pm on Thursday will be processed and dispatched the following day and out for delivery the following Monday (if Next Day Delivery is selected).

- Orders placed after 1pm on Fridays will be processed and dispatched on the following Monday.

For more information about our Shipping & Delivery services click HERE


UK Mainland Delivery Options:


Free Delivery: Applicable for orders of £125 excl. VAT and above
(Monday – Friday, excluding public holidays)


Collect From Store: 41 Markfield Road, London N15 4QA
(Monday – Friday, 9am–5pm excluding public holidays)


Standard Delivery: 3-5 Working Days
(Monday – Friday, excluding public holidays)


Express Delivery: Next Working Day
(Monday – Friday, excluding public holidays)

Out Of Zone Delivery Surcharges:

Isle of Wight

£12.50 per item (3-5 Working Days)

Isles of Scilly

£12.50 per item (3-5 Working Days)

Northern Ireland

£25.00 per item (3-5 Working Days)

Western Isles

£25.00 per item (3-5 Working Days)

Shetland Isles

£30.00 per item (3-5 Working Days)


£30.00 per item (3-5 Working Days)

Isle Of Man

£30.00 per item (3-5 Working Days)

Channel Islands

£30.00 per item

Republic of Ireland

Not Available


paypal confidence