F Ball - F44 Styccobond Acrylic Adhesive

each
Bulk Buy Discount
£32.30
In stock
SKU
F Ball - F44 Styccobond Acrylic Adhesive
  • Available for Next Day Delivery
  • FREE Delivery when you spend over £125

F Ball - F44 Styccobond Acrylic Adhesive

STYCCOBOND F44 is a solvent free acrylic emulsion adhesive, which is designed to give a high bond strength, strong initial tack and a long open time. It is protected against bio-degradation and is suitable for use over normal underfloor heating installations. 

STYCCOBOND F44 can be used for securing vinyl sheet and tile floorcoverings to EN654, EN649 and EN651; rubber floorcoverings and some textile floorcoverings with PVC and polyurethane foam backings.

STYCCOBOND F44 can also be used in conjunction with STYCCOBOND F2 Release Adhesive to provide a RELEASE BOND system. 

STYCCOBOND F44 can be applied to STOPGAP smoothing underlayments, structurally sound, smooth, dry subfloors of concrete and sand/cement screed, plywood, flooring grade chipboard and hardboard.

STOPGAP Waterproof Surface Membranes and sound flooring grade asphalt must be skimmed with a minimum of 3mm of the appropriate STOPGAP smoothing underlayment.

Technical Information:

  • Appearance: Viscous Liquid
  • Colour: Cream / Yellow
  • Available in 15ltr, 5ltr, 2.5ltr and 1ltr capacity
  • Open Time (approx.): Up to 60 minutes depending on temperature, humidity and absorbency of the subfloor
  • Coverage (approx.): 4m2 per litre using a 1.5mm x 5mm trowel
    15 litres Tub = 60m2
    5 litres Tub = 20m2
    2.5 litres Tub = 10m2
    1 litre Tub = 4m2
    Note: Coverage rates will depend on the condition and absorbency of the subfloor

Application:

Holding the trowel at an angle of 60°, spread the adhesive evenly over an area of subfloor that can be covered whilst the adhesive remains receptive and gives good transfer.

On absorbent surfaces - lay the floorcovering immediately, when installing tiles, leave the adhesive for approximately 10 minutes before placing the flooring, to reduce the potential for sliding.

Non-absorbent surfaces - Apply the adhesive and allow to partially dry to a firm tack before laying the floorcovering. When installing impervious sheet floorcoverings, the double drop technique can be used to reduce the time taken waiting for the adhesive to dry. Lay the floorcovering into the wet adhesive, press all over to achieve transfer, then pull it back exposing the adhesive. Leave until the adhesive has dried to a firm tack before replacing the flooring accurately in position.

Roller application - On both absorbent and non-absorbent subfloors, to minimise the effect of adhesive shadowing through vinyl floorcoverings, apply the adhesive then immediately roll with a paint roller, which has been pre-wetted with the adhesive, to obtain a smooth, uniform appearance. Place the floorcovering when the adhesive has dried to a firm tack and is still receptive to the floorcovering.

DO NOT use the roller to extend the stated coverage as this will reduce adhesion

On both absorbent and non-absorbent subfloors, to minimise the effect of adhesive shadowing through vinyl floorcoverings, apply the adhesive then immediately roll with a paint roller, which has been pre-wetted with the adhesive, to obtain a smooth, uniform appearance. Place the floorcovering when the adhesive has dried to a firm tack and is still receptive to the floorcovering.

For any areas under question please consult the F Ball Technical team.

Precautions:

Do not apply loads or move furniture on the floorcovering until the adhesive has fully set. Do not weld vinyl floorcoverings until the adhesive has had sufficient time to develop a good bond, normally 24 hours.

Tools:

STYCCOBOND 1.5mm x 5mm ‘V’ notched trowel, F. Ball 68kg flooring roller, STYCCOBOND Glyda for foam backed carpets and Trimming knife. Tools should be cleaned with warm soapy water while the adhesive is still wet.

Storage:

Store between 5ºC and 30°C. Protect from frost.

Shelf Life:

12 months in unopened containers stored under good conditions.

Delivery Information

We aim to dispatch all orders within 2 working day of receipt. Occasionally public holidays, weekends, weather events, or extremely busy periods may result in extended delivery times. In these circumstances, we will endeavour to communicate with you about the delay and resolve and resulting issues.

Please note that we do not make delivery date promises, however:

- Orders placed before 1pm on a weekday will be processed the same day.

- Orders placed after 1pm on a weekday will be processed the following morning. 

- Orders placed after 1pm on Thursday will be processed and dispatched the following day and out for delivery the following Monday (if Next Day Delivery is selected).

- Orders placed after 1pm on Fridays will be processed and dispatched on the following Monday.

For more information about our Shipping & Delivery services click HERE

 

UK Mainland Delivery Options:

£0.00

Free Delivery: Applicable for orders of £125 excl. VAT and above
(Monday – Friday, excluding public holidays)

£0.00

Collect From Store: 41 Markfield Road, London N15 4QA
(Monday – Friday, 9am–5pm excluding public holidays)

£8.50

Standard Delivery: 3-5 Working Days
(Monday – Friday, excluding public holidays)

£15.00

Express Delivery: Next Working Day
(Monday – Friday, excluding public holidays)

Out Of Zone Delivery Surcharges:

Isle of Wight

£12.50 per item (3-5 Working Days)

Isles of Scilly

£12.50 per item (3-5 Working Days)

Northern Ireland

£25.00 per item (3-5 Working Days)

Western Isles

£25.00 per item (3-5 Working Days)

Shetland Isles

£30.00 per item (3-5 Working Days)

Orkney

£30.00 per item (3-5 Working Days)

Isle Of Man

£30.00 per item (3-5 Working Days)

Channel Islands

£30.00 per item

Republic of Ireland

Not Available

 

paypalconfidence