Ardex - MVS 95 (12kg) One Component Residual Moisture Vapour Suppressant

each
Bulk Buy Discount
£103.00
In stock
SKU
Ardex - MVS 95 (12kg)
  • 2 items +    £101.80
  • 6 items +    £101.20
  • 30 items +    £95.80
 
  • Available for Next Day Delivery
  • FREE Delivery when you spend over £125

Ardex - MVS 95 (12kg) One Component Residual Moisture Vapour Suppressant

ARDEX MVS95 is a ready for use, one component, water based, dispersion coating supplied in pre-gauged 12kg units. ARDEX MVS 95 is supplied pigmented blue to indicate uniform coverage and is waterproof when fully cured. 

ARDEX MVS 95 is designed to suppress residual construction moisture in cementitious substrates including suitably prepared power floated concrete and cement/sand screeds.

ARDEX MVS 95 is designed for use as a two coat system. When fully dry, two coats of ARDEX MVS 95 produces a membrane which can accommodate hygrometer readings up to 95% RH, and allows the subsequent application of ARDEX Levelling and Smoothing Compounds without priming. 

ARDEX MVS 95 can be used on heated screeds that have been installed and commissioned in accordance with BS 8204 Part 1, taking into account the recommendations in Part 4 of BS EN 1264. 

It is not suitable for use on direct to ground substrates without a functioning, structural damp proof membrane. Please refer to the ARDEX DPM 1 C or ARDEX DPM 1 C R datasheet for applications where no structural damp proof membrane exists or the relative humidity is above 95% RH.

Technical Information:

  • Density at 20°C: 1.1
  • Open Time: 20 minutes at 20°C
  • Walkability and over-coating can be achieved in as little as 1 hour at 20°C and 65% RH.
  • Drying time will be extended under cool and/or humid conditions.
  • Colour: Blue
  • Coverage:12kg maximum unit coverage per 2 coat application (m2)
    90% RH = 36m2
    95% RH = 27m2

 

Application:

STIR WELL BEFORE USE. Do not add water or dilute ARDEX MVS 95, it is ready for use. Do not use this product when the air temperature is below 100C and/or the substrate temperature is below 50C. Apply an even coat with a suitable short pile roller in one direction over the appropriate area (see table below). 

Depending on the film thickness applied, and the porosity/absorbency of the subfloor and the ambient conditions, ARDEX MVS 95 may be dry in as little as 30 minutes at 20°C. These times may be extended at lower temperatures and/or in high humidity conditions. When the first coat is touch dry, apply the second coat at right angles to the first.

It is essential that the applied ARDEX MVS 95 is a continuous film and is free from pinholes, cavities or thin patches, otherwise additional applications may be necessary. Allow to dry to a tack free film. This will take approximately 1 hour at 200C in good drying conditions. ARDEX MVS 95 should be overlaid with 3mm, to a maximum 10mm, of an ARDEX Smoothing Compound to protect the film and to provide a uniform absorbent layer for subsequent floorcovering application with an appropriate ARDEX Flooring Adhesive. 

ARDEX MVS 95 must not be trafficked between coats and before the levelling and smoothing compound is applied. No more than 24 hours should be allowed to elapse. 

Packaging, Storage and Shelf Life:

ARDEX MVS 95 is supplied in a 12kg container and is ready to use. It can be roller applied directly out of the container. Part used containers should be resealed after use and the contents will remain usable for at least 6 weeks if stored under good conditions

Store in dry conditions out of direct sunlight & between 5 0C and 300C. Protect from frost. ARDEX MVS 95 has a storage life of not less than 12 months in the original unopened containers.

Delivery Information

We aim to dispatch all orders within 2 working day of receipt. Occasionally public holidays, weekends, weather events, or extremely busy periods may result in extended delivery times. In these circumstances, we will endeavour to communicate with you about the delay and resolve and resulting issues.

Please note that we do not make delivery date promises, however:

- Orders placed before 1pm on a weekday will be processed the same day.

- Orders placed after 1pm on a weekday will be processed the following morning. 

- Orders placed after 1pm on Thursday will be processed and dispatched the following day and out for delivery the following Monday (if Next Day Delivery is selected).

- Orders placed after 1pm on Fridays will be processed and dispatched on the following Monday.

For more information about our Shipping & Delivery services click HERE

UK Mainland Delivery Options:

£0.00

Free Delivery: Applicable for orders of £125 excl. VAT and above
(Monday – Friday, excluding public holidays)

£0.00

Collect From Store: 41 Markfield Road, London N15 4QA
(Monday – Friday, 9am–5pm excluding public holidays)

£8.50

Standard Delivery: 3-5 Working Days
(Monday – Friday, excluding public holidays)

£15.00

Express Delivery: Next Working Day
(Monday – Friday, excluding public holidays)

Out Of Zone Delivery Surcharges:

Isle of Wight

£12.50 per item (3-5 Working Days)

Isles of Scilly

£12.50 per item (3-5 Working Days)

Northern Ireland

£25.00 per item (3-5 Working Days)

Western Isles

£25.00 per item (3-5 Working Days)

Shetland Isles

£30.00 per item (3-5 Working Days)

Orkney

£30.00 per item (3-5 Working Days)

Isle Of Man

£30.00 per item (3-5 Working Days)

Channel Islands

£30.00 per item

Republic of Ireland

Not Available

 

paypalconfidence